Oh, where to begin? Let me start with 'watered down paint'. 25-50% before the material gets to the site? Impossible. You would basically be painting with water at that point. It would be less of a hassle, and cost, to simply use proper material. You would be forced to apply three coats instead of two, as the coverage would be horrible. Whatever cost you think might be saved in materials would be lost in labor. http://www.youtube.com/watch?v=b6_WEt9k_Hw&feature=kp
Here is where this affects you as a consumer. You select a painter with a contract that says 2 coats, $500 down. You give the company the deposit and pick your colors a couple of days before the project starts. The painter goes to the store with your colors and figures out they are deep base. He (or she) not only needs to charge you more for the paint, but he also needs to charge you for a dark gray primer coat. Ninety nine percent of the time that primer coat is going to be really, really expensive since you already gave a deposit.
The Evolution System uses a 100% solids polyurea with unique technology that offers extreme adhesion, rapid cure, and maximum broadcast times. The vinyl flakes come in a variety of blends to mix and match with your choice of basecoat colors. This is one of the most popular systems for because of its wide variety of applications. Walk on in 4 hours & drive on in 24 hours.
Just like with roller paint application, painters are not limited to using just one stroke when cutting in. It is important, however, to work towards the edge of the corners applying even pressure. If time permits, painters should allow their cut in work to dry completely before applying paint with rollers, keeping in mind that light touchups on corners and edges will always be required at the end.
Steve, not only did you come off with an edge regarding the article written for Angie's list but you came awfully close to being slanderous. The article was written if you will have read his bio by a very well established professional painter. The issue regarding the deposit was put in question by a responder. I have read your response in full as you suggested, and companies as large as yours are just as likely to use the tricks of the trade as the small guy as you suggest, if not more so. A large company has less oversight and workers get lazy with the boss not looking over their shoulder. I have had experience in this area, and thought that i was dealing with a very reputable company that had been recommended by a couple friends, my insurance company, and my adjuster who had dealt with the company. I had terrible problems with the company, who do full restorations and like your company paint in all areas. To finalize your statement that Established businesses do not cheat customers is completly false and is a very misleading statement. I am suprised that Angies list allowed you to post such an outragious comment. All you have to do is look in the Civil lawsuits section of the Established businesses that are being sued or are under investigation for fraud and cheating their customers!
When you refinish your existing cabinet doors, you get a whole new look without the astronomical costs normally associated with a kitchen remodel. It’s a much smarter way to update your space, especially if your cabinets are still in good condition. It doesn’t make sense to throw out perfectly good materials, just because you’re tired of the color.
For particularly heavy deposits of paint, heat may be more effective than muscle. One way to apply heat is with an electric paint remover, which is a device with a platelike heating element that "cooks" the paint and has a built-in scraper to pull it off. Wearing heavy gloves, hold the heating element against the surface until the paint sizzles. Pull the remover firmly over the surface. The attached scraper will pull off the cooked paint as you go.
home Painting Design
To determine how much paint your house needs, measure the house's perimeter. Then multiply that figure by the height, excluding gable ends. Take the measurements with a steel tape measure, or reel out a ball of twine around the house and mark and measure the twine. If you will use a different paint on your home's trim, subtract 21 square feet for every door and 15 square feet for each typical window. Divide the final figure by the square-foot coverage specified on the can of paint to determine the number of gallons you will need for one coat.how Much To Paint Contractor
