As you scrape, you may find that the wood has turned gray or black in some areas. Check for rot by probing these areas with a nail. Spots that are discolored but firm are simply weathered. Weathered wood doesn’t hold paint very well, so sand away the gray surface. If you find soft areas, you’ve got rot. Small, shallow soft spots can be dug out and repaired with a two-part filler such as Minwax High Performance Wood Filler. But when rot is deep and widespread, it’s best to replace the entire piece of wood. http://www.youtube.com/watch?feature=youtu.be&v=b6_WEt9k_Hw
The floor and ceiling surfaces cannot be ignored, as they are crucial elements of color combination. Most ceilings are traditionally painted white for a number of reasons — particularly for their ability to keep rooms looking bright and to avoid taking attention away from the walls. Lighter ceiling colors can also help to make a room appear larger and more open.
paintings For Home Walls
When I had my interior painting done, after clearing out all of the furniture, myself, I also removed all of the wall plates in all the rooms to be painted. They were a beige color and probably yellowed. The wall was originally an off white and I had it painted a light-mid grey, so those wall plates would look terrible. After pricing replacement plates, switches and outlets (Would have been way too expensive to replace all of them), I decided to just paint all of the wall plates, switches and outlets (Used just a black gloss spray paint). I sprayed the plates outside and used a small brush on the switches and outlets. It worked out just fine and the blacks plates, etc compliment the wall color. It has been 7 years and the plates, switches, outlets are holding up well.
A primer 3 is essentially a protective layer that you apply before the first coat of paint. If you are painting over an already-painted surface, you may be able to avoid a primer 3 altogether by using a 2-in-1 paint and primer product. However, if you are painting a surface that has never been painted before or changing the paint or finish type, it would be a good idea to prepare the surface using a traditional primer 3. Primers 3 should also be used when painting over hard, smooth surfaces like glass or tile. All three types of primers 3, oil-based, latex-based and shellac-based can be used under latex paint.
Calculate your costs.Having an idea of the cost of paint you need to purchase will help obtain quotes from a contractor. “Paint coverage is based on how many square feet of surface one gallon will cover,” says Bunting. “Most paints will cover approximately 400 square feet. Tally this by multiplying in feet the wall’s height by its width, minus windows and doors.” Determine how much paint is needed to complete the project. “To calculate the cost of a project, factor in the day rates, the size of the property, any architectural features, and the paint finish needed,” says Rance.
Using an airless sprayer to place paint on the wall (using low pressure) will speed up the process because your not having to dip your brush or roller. spray about 3 or 4 sq. ft. and then back brush or roll spreading and evening the paint. Because your using low pressure, mask and cover is at a minimum once you are accustomed to handling the spray gun and the type of surface being painted. Overspray will be larger droplets they tend to fall, than float around.
Even if you go it alone, specialize to keep your initial investment low. If you do only interior painting, for example, you might get by with one ladder, a few brushes, rollers, basic hand tools and such, for an investment of less than $300. Again, you can add to your tools as you need to (every job is a bit different), and parlay profits into the equipment necessary for exterior painting or working on large commercial properties.
For smoothing the edges of scraped spots here and there, you can wrap a piece of sandpaper around a wood block. For larger areas, it's less tiring and more effective to use an electric orbital sander. Move it up and down or back and forth across the surface to remove old paint and smooth rough edges at the same time. Don't use an electric disc sander or a belt sander. Both can leave swirls or dips in the wood that will show through a new coat of paint.
When the primer is dry, caulk all small joints (less than ¼-inch-wide) in the siding and trim. Most pros use siliconized acrylics—paint won't stick to straight silicones—but Guertin and O'Neil like the new, more expensive urethane acrylics for their greater flexibility and longevity. O'Neil stresses that it's shortsighted to skimp on caulk. "If the joint fails, you're back to square one." Guertin uses the lifetime rating as his quality guide. "I don't expect 35-year caulk will last 35 years, but it should last longer than a 15-year caulk."
interior Painters Near Me
At Supreme Painting, our goal is to provide exceptional quality interior and exterior, residential and commercial painting services. We strive to provide these services in the most timely manner, and with an ongoing comprehensive quality control program. If you want the best residential house painter or commercial painting contractor, you can count on Supreme Painting.
Missed appointments, slow arrivals, fuzzy details about deadlines... These are all bright red flags. Punctuality and a sense that your time is valued and appreciated are essential. If it’s a little rocky at the start when they’re still trying to win your business, just imagine what it will be like when the honeymoon phase is over and they have your contract in hand.
