To determine how much paint your house needs, measure the house's perimeter. Then multiply that figure by the height, excluding gable ends. Take the measurements with a steel tape measure, or reel out a ball of twine around the house and mark and measure the twine. If you will use a different paint on your home's trim, subtract 21 square feet for every door and 15 square feet for each typical window. Divide the final figure by the square-foot coverage specified on the can of paint to determine the number of gallons you will need for one coat.
how Much To Paint Contractor
I put out a request for bids to several local house painters and quite a few seemed high. One was for over $6000 for painting the exterior of the house with putty fill as necessary, paint included. It was for him and one other guy to do the work. I said, "it's going to take you guys quite a while to get this job done" and he told me that no, they could do it in 2 days. I don't know about you but $1500 a day per painter seems more than just a bit high. I went with someone else and they had several people there for several days working like crazy and did a great job. There are too many scammers.
Use a wire brush and a wide-blade putty knife to remove small areas of defective paint. Scrub under the laps of clapboard siding as well as on downspouts and gutters. For speedier work on metal, a wire brush attachment on an electric drill will remove rust and paint with less effort. For more extensive paint removal, invest in a sharp pull scraper -- a tool with a replaceable blade that's capable of stripping old paint all the way down to bare wood with a single scrape. Hold the scraper so the blade is perpendicular to the wood, apply moderate to firm pressure, and drag it along the surface. Keep the blade flat against the wood so it doesn't gouge the surface.
If there is any peeling — and there usually is somewhere — it's essential to scrape off any loose paint. This doesn't just mean the parts that are already separated from the wood and ready to fall off on their own. Each spot where paint has peeled loose needs to be scraped thoroughly until you can no longer get the sharp corner of a putty knife under any of the surrounding edges of paint. Then, the bare spot needs to be sanded until the paint edges are smooth.
In my opinion the information on this page should be modified as for the pricing for my area is not correct and the information here could damage the expectations of my or another painting companies pricing. There are too many situations that there is not a way to specify cost prior to seeing the actual house and that information needs to be in big print on this page. http://youtube.com/watch?v=b6_WEt9k_Hw
At Supreme Painting, our goal is to provide exceptional quality interior and exterior, residential and commercial painting services. We strive to provide these services in the most timely manner, and with an ongoing comprehensive quality control program. If you want the best residential house painter or commercial painting contractor, you can count on Supreme Painting.
The article was well-intended, but it makes it sound like painters are the crooks and consumers are innocent victims. That is blatantly un-true. Maybe there should be a follow-up article that educates consumers how not to be shysters by expecting a ton more than they said at the start, or not paying the balance of the job unless something else is done that was not in the contract. Tradesmen have a rough road when dealing with consumers that have short arms but long lists of by-the-way items. No, I'm not a painter...
To maintain a wet edge, start near a corner and run the roller up and down the full height of the wall, moving over slightly with each stroke. Move backward where necessary to even out thick spots or runs. Don’t let the roller become nearly dry; reload it often so that it’s always at least half loaded. Keep the open side of the roller frame facing the area that’s already painted. That puts less pressure on the open side of the roller, so you’re less likely to leave paint ridges when doing DIY wall painting.
As you scrape, you may find that the wood has turned gray or black in some areas. Check for rot by probing these areas with a nail. Spots that are discolored but firm are simply weathered. Weathered wood doesn’t hold paint very well, so sand away the gray surface. If you find soft areas, you’ve got rot. Small, shallow soft spots can be dug out and repaired with a two-part filler such as Minwax High Performance Wood Filler. But when rot is deep and widespread, it’s best to replace the entire piece of wood. http://www.youtube.com/watch?feature=youtu.be&v=b6_WEt9k_Hw
We provide pressure washing and sealing services for decks and fences. We all so offer pressure washing services for your exterior home needs. Need a professional pressure washer contractor in Virginia Beach? Call (757) 383-0344 now to get a competitive quote at your Hampton Roads location. Virginia Beach Pressure Washing We look forward to working …
Before the scrubdown, protect nearby plants by misting their leaves and saturating the surrounding soil with water, pulling them away from the house, and shrouding them in fabric drop cloths. (Plants will cook under plastic.) Lay more drop cloths along the base of the walls to collect any falling paint debris. Walls should be wet down before getting scrubbed, then washed with a gallon of water mixed with 1 cup chlorine bleach and 1 cup of either a concentrated, phosphate-free cleaner, such as a trisodium phosphate (TSP) substitute, or Jomax House Cleaner. Working in sections, from the bottom to the top, will avoid streaks. Be sure to rinse walls well before the solution dries. Wood siding and trim should be ready to paint after a day or two of dry weather. http://www.youtube.com/v/b6_WEt9k_Hw&feature=share
The last big decision is how to apply the paint. Most pros use paint sprayers because they're fast, but in inexperienced hands a high-powered sprayer can leave drips, thin coats, and a mist that may land on many things other than your siding. If you do hire a painter who uses a sprayer, make sure he is meticulous about removing, covering, or masking off everything in the area that might get hit with overspray: gutters, roofs, windows, shrubbery, walkways, cars—you name it.
When coverage is difficult to estimate, add more rather than less when doing DIY wall painting. You can always pour the leftover back into cans. For large jobs, use the bucket and a roller screen rather than a roller tray. It’s much faster to load your roller with the screen than to use a roller pan. Simply dunk the roller into the paint bucket, then roll it along the screen until it stops dripping. https://youtube.com/watch?v=b6_WEt9k_Hw
Shopping for the right paint should go beyond collecting paint swatches or choosing a shade from the catalogue. Purchasing inexpensive paint samples and small brushes to bring home for testing is the best, because it's the only way to really ascertain whether a color suits the décor. The goal is to paint a small section of the wall — a square with an area of just a few inches is sufficient. Allowing the small painted patch to dry and observing how it looks under the lighting conditions at different times of the day should clear up any painter’s color dilemma.
To determine how much paint your house needs, measure the house's perimeter. Then multiply that figure by the height, excluding gable ends. Take the measurements with a steel tape measure, or reel out a ball of twine around the house and mark and measure the twine. If you will use a different paint on your home's trim, subtract 21 square feet for every door and 15 square feet for each typical window. Divide the final figure by the square-foot coverage specified on the can of paint to determine the number of gallons you will need for one coat.
